BRIMNES Cabinet with doors, white, 30 3/4x37 3/8″
+6⅝″ margin
All items that fit a Dacia Duster 2023
Will fit in a ?
No, it won't fit.
It will not fit in this setup: LISABO Table, ash veneer, 55 1/8x30 3/4″ is too large for a Dacia Duster 2023 with seats up.
Fit Details
With seats up, This package will not fit in this setup. The blocker is opening width, and you're short by 8⅞″ even with diagonal loading. We're about 95% confident in this estimate.
LISABO Table, ash veneer, 55 1/8x30 3/4″
Box: 64¾″ × 32″ × 2″ · 45 lb
Based on IKEA US (United States).
Package dimensions last checked and updated on Oct 21, 2026
Package
Status
Limiting factor
Best orientation
Package #1
64¾″ × 32″ × 2″
Status:8⅞″ short
Limited by
Limiting factor:Opening width
Best orientation:Diagonal
Vehicle limits
Opening width / height above sill
38⅝″ / 28¾″
Cargo width / height
39⅜″ / 31⅞″
Cargo length seats up / down
38¼″ / 64⅝″
Loading sill height
29⅞″
Dacia Duster 2023
Measurements last checked and updated on Oct 21, 2026
Helpful tips
Use these loading tips to improve your chances of fitting LISABO Table, ash veneer, 55 1/8x30 3/4″ in Dacia Duster 2023.
Optimize opening width
Keep the narrow edge leading while entering the opening.
Load diagonally first
Load diagonally first, then straighten once inside.
Try fitting alternatives
Check the Similar items that fit section for safer alternatives.
Alternatives that fit in Dacia Duster 2023
Ranked by fit margin and package-dimension similarity. This improves as we index more items.
About the Dacia Duster 2023 boot
In the Duster's boot, the opening is the narrow point. It is 38⅝″ wide with 28¾″ of clear height above the loading sill, while the floor never narrows below 39⅜″. The floor is 38¼″ long with the rear seats up, which suits a few boxes, and 64⅝″ with them folded, 26⅜″ more, for long flat packs. Every box needs a proper lift first: the loading sill is 29⅞″ high, with the floor 3⅛″ lower. Before you lift the next box, push the last one all the way in, so the sill stays clear.
About the LISABO Table, ash veneer, 55 1/8x30 3/4″ package
One flat box holds the whole LISABO table: 64¾″ × 32″ × 2″, at 45 lb. At only 2″ thick and 32″ wide, it is too thin to grip well and too broad to carry under one arm. Lying flat and straight, it needs 64¾″ of boot floor, and the opening has to clear that 32″ width one way or the other. Carry it between two people, one at each short end, with your hands under the box rather than pinching the thin edges, and keep it level as you lift it and set it down.
Frequently asked questions
Find quick answers about fit for LISABO Table, ash veneer, 55 1/8x30 3/4″ in Dacia Duster 2023, including seats up vs seats down, limiting factor, best orientation, and package-by-package margins.
Will LISABO Table, ash veneer, 55 1/8x30 3/4″ fit in Dacia Duster 2023?
No. With seats up, it is short by 8⅞″ at Opening width, even with diagonal loading.
What is the tightest part?
The limiting factor is Opening width, with -8⅞″ margin in seats up.
Why does it not fit?
The blocker is Opening width: with seats up, the box is 8⅞″ bigger than the space there.
Can I load it diagonally?
Yes, diagonal is the best orientation for this check, with -8⅞″ around the limiting point.
Which loading orientation works best?
Diagonal is the best orientation for this result in seats up.
Does it fit with seats up or seats down?
Seats up: No (-8⅞″). Seats down: No (-¼″). Default selection follows YES > MAYBE > NO.
What do YES, MAYBE and NO mean here?
YES means there is at least 2⅜″ to spare at the tightest point, in the best way the box can go in. MAYBE means it fits on paper, but with less than 2⅜″ to spare, so trim, the parcel shelf or the loading angle can decide it. NO means the box is bigger than the space at its tightest point, whichever way it goes in. Every margin on this page is that real gap: the car's measurement minus the box's.
What should I do instead?
Use the Helpful tips & alternatives section to choose a smaller item, different orientation, or split-load plan.
Is the trunk opening the issue?
Yes. The tightest constraint is at the opening (Opening width) with -8⅞″ margin.
How tight is this fit?
This result is in the clear no-fit band (-8⅞″ at Opening width).