BESTÅ TV unit, white, 47 1/4x15 3/4x25 1/4″
+11⅛″ margin
All items that fit a Toyota C-HR 2020
Will fit in a ?
Yes, it will fit!
Good news: FJÄLLBO Shelf unit, black, 20 1/8x53 1/2″ should fit diagonally in a Toyota C-HR 2020 with seats down.
Fit Details
With seats down, Good news - this package should fit, with 10″ to spare at opening height when loading diagonal. We're about 95% confident in this estimate.
FJÄLLBO Shelf unit, black, 20 1/8x53 1/2″
Box: 53″ × 14¾″ × 3¾″ · 24 lb 4 oz
Based on IKEA US (United States).
Package dimensions last checked and updated on Oct 21, 2026
Package
Status
Limiting factor
Best orientation
Package #1
53″ × 14¾″ × 3¾″
Status:+10″ to spare
Limited by
Limiting factor:Opening height
Best orientation:Diagonal
Vehicle limits
Opening width / height above sill
27½″ / 24¾″
Cargo width / height
37¾″ / 26⅜″
Cargo length seats up / down
30⅜″ / 62⅝″
Loading sill height
30⅜″
Toyota C-HR 2020
Measurements last checked and updated on Oct 21, 2026
Helpful tips
Use these loading tips to improve your chances of fitting FJÄLLBO Shelf unit, black, 20 1/8x53 1/2″ in Toyota C-HR 2020.
Manage opening height
Keep the highest edge low at the trunk opening.
Load diagonally first
Load diagonally first, then straighten once inside.
Other items to check in Toyota C-HR 2020
Ranked by fit margin and package-dimension similarity. This improves as we index more items.
About the Toyota C-HR 2020 boot
The C-HR's opening is narrower than its boot. It is 27½″ wide with 24¾″ of clear height above the loading sill, while the floor behind it stays 37¾″ wide at its narrowest. That sill sits 30⅜″ off the ground, and the floor is only 1⅝″ lower. Seats up, you get 30⅜″ of floor. Folding the rear seats adds 32¼″, a big gain, for 62⅝″ in total, though a box that passes the opening can still be too long for that floor. Bulky boxes are the poor match. Check every box against the opening before you think about the floor.
About the FJÄLLBO Shelf unit, black, 20 1/8x53 1/2″ package
Everything for this FJÄLLBO shelf unit is in one flat box: 53″ long, 14¾″ wide and just 3¾″ thick. It weighs 24 lb 4 oz, which is a lot for a box that thin, and the narrow edges give your hands very little to hold. For the box to lie straight, the boot needs 53″ of floor and 14¾″ across. Carry it upright on its long edge, tucked under one arm with your other hand under the bottom, so the weight hangs at your side and the corners stay off the ground.
Frequently asked questions
Find quick answers about fit for FJÄLLBO Shelf unit, black, 20 1/8x53 1/2″ in Toyota C-HR 2020, including seats up vs seats down, limiting factor, best orientation, and package-by-package margins.
Will FJÄLLBO Shelf unit, black, 20 1/8x53 1/2″ fit in Toyota C-HR 2020?
Yes. With seats down, it fits with 10″ to spare at Opening height. Best orientation: diagonal.
What is the tightest part?
The limiting factor is Opening height, with +10″ margin in seats down.
Do I need to fold the seats?
Results differ by configuration. Seats up is No and seats down is Yes.
Is the trunk opening the issue?
Yes. The tightest constraint is at the opening (Opening height) with +10″ margin.
How tight is this fit?
This result is in the comfortable clearance band (+10″ at Opening height).
Does it fit with seats up or seats down?
Seats up: No (-11⅛″). Seats down: Yes (+10″). Default selection follows YES > MAYBE > NO.
What do YES, MAYBE and NO mean here?
YES means there is at least 2⅜″ to spare at the tightest point, in the best way the box can go in. MAYBE means it fits on paper, but with less than 2⅜″ to spare, so trim, the parcel shelf or the loading angle can decide it. NO means the box is bigger than the space at its tightest point, whichever way it goes in. Every margin on this page is that real gap: the car's measurement minus the box's.
Can I load it diagonally?
Yes, diagonal is the best orientation for this check, with +10″ around the limiting point.
Which loading orientation works best?
Diagonal is the best orientation for this result in seats down.
How confident is this result?
Confidence is 95 out of 100 based on available dimensions and margin tightness.