
LAGKAPTEN / ADILS Desk, white, 55 1/8x23 5/8 "
+4¾″ margin
Maybe, it's a tight fit.

Fit Details

DÄNKA Ironing board, 47 ¼x14 ½ "
Box: 60″ × 15½″ × 2¼″ · 12 lb 8 oz
Based on IKEA US (United States).
Package dimensions last checked and updated on Aug 24, 2026
Package
Status
Limiting factor
Best orientation
Package #1
60″ × 15½″ × 2¼″
Status:+⅞″ tight
Limited by
Limiting factor:Opening width
Best orientation:Diagonal
Vehicle limits

Opening width / height
37″ / 32¼″
Cargo width / height
40⅛″ / 40⅛″
Cargo length seats up / down
26⅜″ / 56¾″
Loading sill height
30¾″
Renault Captur 2024
Measurements last checked and updated on Jul 08, 2026
Helpful tips
Use these loading tips to improve your chances of fitting DÄNKA Ironing board, 47 ¼x14 ½ " in Renault Captur 2024.
Optimize opening width
Keep the narrow edge leading while entering the opening.
Load diagonally first
Load diagonally first, then straighten once inside.
Clear real-world obstacles
Clear the trunk before loading. Existing cargo, trunk cover, and wheel-arch bumps can reduce usable space.
Alternatives that fit in Renault Captur 2024
Ranked by fit margin and package-dimension similarity. This improves as we index more items.
About the Renault Captur 2024 boot
The Captur gives you a compact, upright boot rather than a long one. Behind the rear seats the floor runs about 26 3/8 inches, so tall or square boxes load fine but anything long sits at an angle. The opening is 37 inches wide and 32 1/4 inches tall, and there is a 7 7/8 inch drop from the sill down to the floor, so you lift over a lip then set down. Fold the rear bench and the floor stretches to 56 3/4 inches, a gain of 30 3/8 inches that changes what the car can take. Slide long boxes in low and straight down the 40 1/8 inch centre channel.
About the DÄNKA Ironing board, 47 ¼x14 ½ " package
One box, 60″ × 15½″ × 2¼″, at 12 lb 8 oz: the DÄNKA is light enough to carry one-handed and long enough to be awkward anyway. Weight is not the problem; length is. A 60″ slab will not sit crosswise in a normal trunk, so it rides diagonally or waits for a folded seat. Nearly any hatchback takes it with the bench down, a wagon or SUV swallows it flat, and it can angle across the rear seat of a sedan in a pinch. Feed it nose first through the opening and keep it supported along its length; a carton only 2¼″ thick flexes if you bridge it, and the corners dent before anything else.
Frequently asked questions
Find quick answers about fit for DÄNKA Ironing board, 47 ¼x14 ½ " in Renault Captur 2024, including seats up vs seats down, limiting factor, best orientation, and package-by-package margins.
Will DÄNKA Ironing board, 47 ¼x14 ½ " fit in Renault Captur 2024?
Maybe. With seats down, this is a borderline fit at Opening width (+⅞″). Best orientation: diagonal.
What is the tightest part?
The limiting factor is Opening width, with +⅞″ margin in seats down.
Do I need to fold the seats?
Results differ by configuration. Seats up is No and seats down is Maybe.
Is the trunk opening the issue?
Yes. The tightest constraint is at the opening (Opening width) with +⅞″ margin.
Which loading orientation works best?
Diagonal is the best orientation for this result in seats down.
Does it fit with seats up or seats down?
Seats up: No (-14⅝″). Seats down: Maybe (+⅞″). Default selection follows YES > MAYBE > NO.
What can I try to make it work?
Use diagonal loading and focus on opening width. Keep the narrow edge leading while entering the opening. Load diagonally first, then straighten once inside.
Can I load it diagonally?
Yes, diagonal is the best orientation for this check, with +⅞″ around the limiting point.
What could change the result in real life?
Cargo liners, wheel-arch bumps, the trunk cover, and items already in the trunk can reduce usable space. Measure the tightest point if the fit is close.
How tight is this fit?
This result is in the borderline band (+⅞″ at Opening width).